Key Features: One-piece structure, Super printing size 220220250mm. Comes with several assembled parts, simple assembly, only 120 minutes for 3D printer beginners before the first printing. Big hand twist nut, easier to level.Safety protected Power supply, reach 110 for hotbed in about 5 minutes. The resume printing function can resume prints even after a power outage or lapse occurs. Removable Build Plate to replace reprinting tape and glue, solve warping problem. V1.1.4 Standard Version motherboard comes with thermal runaway protection. The board is only the Standard Version, Not-Silent.
Product description: 3D Technology FDM Max Traveling Speed180mm/s Filament1.75mm PLA Layer Thickness0.1-0.4mm Nozzle diameter0.4mm Precision±0.1mm InputAC 100-265V 50-60Hz OutputDC 24V 15A 360W Max Nozzle Temperature255 Max Hot bed Temperature110 Printing Size220220250mm Machine Size440410465mm Package weight8.6kg File Format STL, OBJ, G-Code Working Mode Online or SD offline Package content. Creality Ender 3 3D printer. Filament does not stick on the hotbed?
For newcomers, this is the most common problem. Do not worry, you can solve it easily. Generally, the distance between the nozzle and platform is too far or near. So rotary the knob under the platform to adjust the distance between the nozzle and platform again, at a piece of A4 paper distance or less. The display shows "Min temp"?
This happens for the following reasons: 1. Thermistor port of nozzle is not plugged into the motherboard above or poor contact; 2.The Thermistor port of the nozzle is broken, you need to replace the spare thermistor. The display shows "MAX temp"? This happens for the following reasons. Thermistor port of nozzle screw is locked tightly, cause the temperature can not be sensing. Thermistor port of the nozzle is broken, you need to replace the spare thermistor. Axis movement is not normal? Please check axis lines and limit lines whether the one-to-one correspondence, whether loose. When you check the extruder motor, you must preheat the nozzle over 185. Circles not round, Lines not touching? If the X/Y belt is loose, you can find circles that are not round, Lines not touching when printing. Tighten all belts as far as possible. How to level Creality Creality Ender 3? Move the nozzle so that it's positioned over the left corner of the bed. A half-inch or so from both sides is a good location. Slide the paper between the nozzle and the bed.
If it doesn't fit, drop the corner until it does. Once the paper is able to slide under the nozzle, very slowly raise the corner with the adjuster.Remember: Clockwise moves the bed up. As you do this, gently slide the paper back and forth. The moment you feel even the slightest resistance to your moving the paper, stop turning the knob. That corner is (almost) ready to go.
Do the same for the other three corners of the build plate. Always advance the hot end to a new corner slowly. This will prevent damage to the build plate in case the nozzle starts to drag. If this occurs, simply lower the next corner (before starting the leveling process) to make some room. After you've adjusted each corner once, go back and check the four corners again.You may have to do further adjustments to get all four correct. Does Creality Ender 3 need to be assembled all by itself? No, Ender 3 is a semi-assembly machine. You can refer to our packing instructions for assembly.
Its installation is quite simple. How long will it take to install Creality Ender 3? The specific installation time depends on the user's familiarity with the product. If you are familiar with the product and can fully understand the installation instructions, it will take about 30 minutes.If you don't know much about a 3D printer, it takes about two or three hours. What filament does Creality Ender 3 use for printing? Creality ender 3 how to change filament? Step 1: Adjust the nozzle temperature to the consumable melting temperature and remove the consumables to be replaced. Step 2: Push the new filament along until you feel firm resistance. This means it has reached the nozzle. Step 1: Set the heating temperature, eliminate old consumables, and make new prints. We only sell Genuine Creality 3D Printer with Brand logo and model on any component. The item "2021 Newest 3d printer Creality Ender 3 3D Printer 220X220X250mm DC 24V US Stock" is in sale since Thursday, April 5, 2018. This item is in the category "Computers/Tablets & Networking\Printers, Scanners & Supplies\Printers". The seller is "christmas-gift" and is located in Hebron, Kentucky.
This item can be shipped to United States.